Do not spill any liquid or spray any chemical-containing liquid over the equipment. Use a dry soft cloth to wipe off stains and dust from the surfaces of the main body case. For severe soiling, dip the cloth in water and wring it, for wiping off the soil. Page 13 4. Do not install the printer near a heater or in a place exposed to the direct sunshine. Page 17 : 50 million pulses or more Print rate Page 2. Discoloring starts at about 70 C. Watch out for effects of heat, humidity, light, and so on.
Do not use the label paper when the printer has been set for thermal paper, and vice versa. Be careful not to mistake a type of label paper. Page Outer Appearance And Component Parts Illuminated at the time of a head-up mechanical error, and blinks at the time of starting a macro. Page Operation 1. Turn off the power. Connect the cable connector of the AC adapter to the power connector located on the back of the printer.
Connect the AC power cord of the AC adapter, and plug it into a socket. Page Connecting Interface Cable 3 Connect the interface cable securely. Otherwise, communications may not be obtained due to a connection failure. Serial interface : Tighten screws, to fix it.
Parallel interface : Turn a stopper, to fix it. Page Inserting The Paper 4 Do not hold or press the paper roll while printing, because it could cause a paper jam. Note that if data is remaining in the buffer, the printer will start printing after the paper is set. Page Eliminating The Paper Jam 4 Do not detach the platen roller unit unless necessary, such as for a paper jam.
If some data are still remaining in the buffer, printing will be resumed after replacing the paper. Replace the paper according to "4. For details, see "4. If the paper end sensor, near paper end sensor, and head-up lever are cancelled, the paper will be automatically fed by a constant amount in about 1 second.
The printer cannot feed the paper or print. Head overheat Page 31 3 Do not perform high-energy print on the single-color paper regular thermal paper.
It may deteriorate the service life of the thermal head or the printing quality. Detach the printer cover, and take out the paper roll. The switch is found under the paper roll. There are 2 switches 8-pole and 4-pole for the serial interface, and 1 switch 8-pole for the parallel interface.
It could cause trouble, etc. Short Open See Table 3 7 bits At this time, all the control circuits in the printer stop. Negative logic : Output if the printing paper has run out or is running out. Page Input And Output Signals If it is a mark, the system will not recognize the bit as the start bit and try to detect the start bit again without judging it as an error. Page Power Connector 2 Do not connect the power source with different polarity.
Page Page Command Details [ ]k in the table denotes k-times of repeat. Page 45 For details, see the manual for the language used. Page 47 The head of the line becomes the next print starting position.
Page 51 [Example] Create each data bit by setting "1" for a printed dot and "0" for an unprinted dot. Page 52 When the values set in m Bit image mode are out of the above range, the data following after n1 is processed as normal printing data.
After completion of bit image printing, printer returns to normal data processing mode. When the printer is deselected, this printer discards all the data until it is selected with this command. Page Esc G N Specified volume does not remain. The beginning of the line is to be considered as the next printing start position. Initial value is not defined. France Germany U. Page Esc C 3 N This printer can only select one kind of paper-end detection, a paper-near-end sensor.
LF SW invalid. If a value lower than the already set value is set at PNE detection time, the printer may stop printing. The set value remains valid until it is re-set or the printer is turned on again. Page 68 Specifying exceeding the top of line or the end of line is ignored. Page 69 "0" stationary. A column numeral entered from the host or application software is compressed to 8 columns with a check column and printed.
If a reverse-polarity connection is made, internal elements may be broken or a mating device may be adversely affected. Do not route the cable too long or connect it to a noisy device.
Connection to a noisy device could cause erroneous printing due to corrupt data, and so on. Do not handle the equipment in the following manners, because problems may result. Also, do not use the AC adapter for other purposes. It could damage the printing head. It could cause the paper to jam. Use of other paper could deteriorate the print quality or cause a problem with the printing head. Your finger may be cut. Do not disassemble the equipment on your own.
For severe. Never use organic solvents, such as. Be careful not to damage the printing head. Be careful not to touch them immediately after printing. Do not touch the heating surface of the head with a bare hand or metal. Referring to "4. Moisten gauze slightly with alcohol, and clean the heating surface of the printing head with it. Reattach the platen roller unit. When detaching or reattaching the platen roller unit, be sure to raise up the printing head; otherwise, they could be damaged.
Handle the detached platen roller unit carefully so as not to damage it. Model Classifications Basic Specifications Paper Specifications Recommended Paper Printing Position Connecting AC Adapter Connecting Interface Cable Inserting the Paper How to Remove Remaining Paper Roll Eliminating the Paper Jam Paper End Function Paper Near End Function Auto-Loading Function Self-Print Function Operation Panel and Display of Error Location of DIP Switch DIP Switch Function Jumper Wire Function Connector's Pin Configuration Input and Output Signals Electrical Characteristics Timing Chart Data Receiving Control Data Configuration Error Detection Command List Command Details International Character Codes Table Einsetzen des Papiers Entnehmen der eingesetzten Papierrolle Beheben von Papierstau Bedienfeld und Fehleranzeigen Lage der DIP-Schalter This small line thermal printer is designed for various types of data communication terminals and measuring instrument terminals.
Its abundant built-in features allow you to widely use this printer for different applications. Prior to using it, read and understand this manual thoroughly. Small, lightweight, and installable in a narrow area. High speed and low noise, owing to line thermal print. Long-life printing head and high reliability, owing to the simple mechanism. Easy paper-loading, owing to the auto-loading function.
Capable of printing a bar code Special command. Capable of accommodating both thermal paper and label paper. A little discharge 1 sheet of the label paper at power-on or paper replacement.
Capable of printing in two colors when special paper is used. External characters registration function 94 kanji characters, 95 ANK characters. If such condensation should form, do not turn on the power until it has completely gone away. Do not use it for any other purpose. Use of non-specified paper may cause irregularity of print density. If this is the case, use the DIP switch to reset print density.
See 5. Do not paste the paper to the core. If the paper comes in contact with a chemical or oil, it may discolor or lose a record. Do not rub the paper surface strongly with a nail or hard metal. It may discolor. Watch out for effects of heat, humidity, light, and so on. Do not use the label paper when the printer has been set for thermal paper, and vice versa. Be careful not to mistake a type of label paper. It could cause malfunctioning or damage the printing head.
Illuminated at the time of a head-up mechanical error, and blinks at the time of starting a macro. Illuminated when the paper is running out when there is little paper left , and blinks when a label paper cut is specified. Feeds the paper. It is fed continuously while the switch is held down. For the label paper, it is fed by one label. Connects to a communication interface cable. There are two types, for serial and parallel interfaces. Connect the cable connector of the AC adapter to the power connector located on the back of the printer.
Connect the AC power cord of the AC adapter, and plug it into a socket. Its coating can melt and cause a fire or electric shock. Connect to a power source with sufficient capacity. If the capacity is insufficient, a fire may result from heat generation. Turn off the power. Mating side included. Check the top and bottom of cable terminals, and connect to the interface connector. Wrong wiring could cause trouble or malfunctioning to not only the printer body but also the host computer.
Pulling the cable itself may snap the internal wires. Otherwise, communications may not be obtained due to a connection failure.
It could cause malfunctioning of the printer or damage the printing head. Hold the convexity on the rear of the printer cover, and raise it upward. Cut the front end of the paper roll almost at a right angle.
After detaching it, be careful not to lose or break it. Make sure that the power is turned on. Pull the head-up lever to this side to raise up the printing head. If there is still some paper remaining after a paper-out indication, eliminate the paper roll according to "4.
Insert the front end of the paper roll straight into a paper insertion slot. Set the paper roll firmly in the paper holder. Put back the head-up lever. The paper roll is automatically pulled in by the platen roller to feed a.
When auto-loading is enabled. For the label paper, it is fed to the print. Note that if data is remaining in the buffer, the printer will start printing after the paper is set. Gently pull out the paper to the near side. If the paper roll is still remaining, cut it just before the paper insertion slot before pulling it out.
Cut the paper roll near the paper insertion slot. Raise the blue levers located on both sides of the platen roller unit, to gently detach the unit. The platen roller unit can be detached by manually raising the blue levers.
Remove the remaining paper roll completely from the paper passage. If the label paper is used, some paste may be adhered. Dip soft cloth, etc. Confirming the direction of the platen roller unit, reattach it to the mechanism.
Shift down the blue levers on both sides, to fix the unit. Pressing the switch, feed the paper by 1 line. If the switch is held down, the paper will be fed continuously. If the switch is held down for 1 second or more, the paper will be fed by one label. The waiting state continues until the switch is pressed. After cutting the paper, pressing the FEED switch searches for the head of the. If the label paper is fed by 1 line by pressing the FEED switch, the label head position will be dislocated.
Note that if printing starts in this state, the label will be printed dislocated. It is recommended to feed the paper by 1 label. If some data are still remaining in the buffer, printing will be resumed after replacing the paper.
Replace the paper according to "4. For details, see "4. If the paper is running out, the PNE sensor informs the host computer that the paper is running out, by means of a signal output or the PAPER lamp on the panel. At initial setting. Printing is allowed up to about 1. Replace the paper according to the procedure in "4. The output state can be changed by the DIP switch or a command. PNE is detected when the remaining amount of the paper roll is about 2 3 m.
It depends on the paper quality used, paper thickness, and operating environment. An initial value is 1. Up to 1. At this time, with the approx.
It can be adjusted between 0 and 2. Adjust it depending on the operating environment and paper quality. Depending on an adjustment value, paper end may be detected Printing stop first. If PNE is detected at power-on, a set amount of printing will be done from that point. The default is 1. This printer has a function to automatically set the paper. If the paper end sensor, near paper end sensor, and head-up lever are cancelled, the paper will be automatically fed by a constant amount in about 1 second.
Up to the print start position of the second sheet in the case of label paper. If disabled, auto-loading will not be performed. The paper is fed to the print start position in the case of label paper. This printer has a function to perform preset printing. Turn on the power with the FEED switch held down. After self-printing is completed, the printer restores its normal operating conditions.
In the case of label paper, it is fed to the print start position of the next label. See "4. The red and black two-color thermal paper changes its colors by controlling the energy applied to the.
0コメント